To disconnect a cord, hold down the release tab and pull out the connector. Never pull the cord itself. Be sure to connect matching speaker terminals e. If your TV set does not, set the volume on your TV set to minimum. After making the connection as shown above, turn up the volume on the TV set. Your TV must also be connected via an S-video connector.
S- video signals are on a separate bus from the video signals and will not be output through the video jack. With its built-in amplifier, this speaker system can be used to output audio and video signals directly from such components as LD players, MD decks, digital satellite receivers, and VCRs. Do not connect an amplified audio source. If you wish to hang the rear speakers on a wall with hooks not supplied , use the supplied black wood screws to attach the supplied mounting brackets to the upper part of the back panel of each rear speaker.
After connecting all the components, speakers, and AC power cord, output a test tone to check that all the speakers are connected correctly. For details on outputting a test tone, see page If no sound is heard from a speaker while outputting a test tone or a test tone is output from a speaker other than the one whose name is currently displayed on the front panel display, check the speaker connection again.
A dummy disc is placed in the DISC 1 tray at shipment to prevent damage to the system during transportation. Before using the system for the first time, remove the dummy disc following the steps below. Be sure to keep the dummy disc in a secure place. You can select the language for the setup display, the Control Menu display or the messages displayed on the screen. The languages you can select are the ones displayed in Step 2.
For details, see page For the best possible surround sound all the speakers other than the subwoofer should be the same distance from the listening position A. However, this system lets you to place the center speaker up to 5 feet closer B and the rear speakers up to 15 feet closer C to the listening position.
The front speakers can be placed from 3 to 15 feet A from the listening position. You can place the rear speakers either behind you or to the side, depending on the shape of your room, etc. Do not place the center and rear speakers farther away from the listening position than the front speakers. For better surround sound quality, position each speaker as shown below.
Each rear speaker should be placed as its tweeter is on the inner side. The grille can be detached to visually verify the orientation. To obtain the best possible surround sound, first specify the distance of the speakers from your listening position, then set the balance and level.
Use the test tone to adjust the speaker volumes to the same level. If you do not operate the remote for a few seconds, the parameter turns off and is stored in the system. You can vary the distance of each speaker as follows. The default adjustments are in the parentheses.
Center speaker distance can be set in 1 foot steps from a distance equal to the front speaker distance to a distance 5 feet closer to your listening position. Rear speaker distance can be set in 1 foot steps from a distance equal to the front speaker distance to a distance 15 feet closer to your listening position. If each of the front or rear speakers are not placed an equal distance from your listening position, set the distance of the closest speaker.
You can specify the position and height of the rear speakers. The default settings are underlined. They are to be used when you customize sound fields. See page If you do not operate the remote for a few seconds, the value turns off and is stored in the system. You can vary the balance of each speaker as follows.
You can vary the level of each speaker as follows. You can preset 20 stations for FM and 10 stations for AM. Before tuning, make sure that you have turned down the volume to the minimum. Scanning stops when the system tunes in a station. Refer to the instructions supplied with your disc. Press A of the same disc tray number to close the disc tray.
The system starts playback continuous play of the disc whose disc tray indicator is green. You can play the disc interactively, following the instructions on the menu screen.
PBC Playback, see page However, if Program Play is on, you can only start playback by pressing the H button. To make the screen saver image go away, press H. If you want to set the screen saver function to off, see page Press A to close the disc tray.
You can enjoy surround sound simply by selecting one of the pre-programmed sound fields according to the program you want to listen to. Whenever you select a program source, the sound field that was last applied is automatically applied again.
With the tuner, sound fields are memorized separately for all preset stations. When you play sound tracks with 96 kHz sampling frequency, the output signals will be converted to 48 kHz sampling frequency. The effects provided by the virtual speakers may cause increased noise in the playback signal. Discs Playing. The letters L, C, R, etc. The boxes around the letters vary to show how the system downmixes the source sound based on the speaker settings.
When using music sound modes like HALL, the system adds reverberation based on the source sound. However, a center speaker signal is not created. In this case, sound is output from the rear speakers, but output channel indicators for the rear speakers do not light. Welcome to ManualMachine. We have sent a verification link to to complete your registration.
Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions.
Enter a new password. This label is located on the Laser protective housing inside the enclosure. The following caution label is located inside of the unit. This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance. Settings and Adjustments Back cover 3. Icon Meaning Z Indicates that you can use only the remote to do the task.
Indicates the functions for Audio CDs. The Data Precision digital multimeter is suitable for this job. The "limit" indication is 0. Nearly all battery operated digital multimeters that have a 2V AC range are suitable.
See Fig. A Fig. Using an AC voltmeter to check AC leakage. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This caution label is located inside the unit. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.
Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. Grille Frame B Assy Amplifier Assy Amplifier Chassis AMP Board Power Transformer T PS Board Mechanism Section Video Board Magnet Assy Page 21 Press H.
The system starts playback continuous play of the disc whose disc tray indicator is green. Reproduces the sound characteristics of the Sony C. Page 23 Sound field Effect V. The boxes around the letters vary to show how the system downmixes the source sound based on the speaker settings. When using music sound modes like HALL, the system adds reverberation based on the source sound. Page Customizing Sound Fields Customizing Sound Fields By adjusting the surround parameters of the front, rear and center speakers, you can customize the sound fields to suit your particular listening situations.
Once you customize a sound field, the changes are stored in memory indefinitely unless the system is unplugged for about a day. Page 27 Adjusting the equalizing parameters You can adjust the bass and treble levels and select the subwoofer mode. The settings available here are stored individually for each sound field. As long as you do not open the disc tray, Resume Play is available even if you turn the power off. When you play these DVDs, you can select the language for the subtitles, the language for the sound, etc.
Using the Control Menu Display Using the Control Menu display, you can select the start point, change the angles, etc. In Dolby Digital format, the signals from monaural to 5. Depending on the DVD the number of the recorded channels may be different. With DVDs on which multilingual subtitles are recorded, you can change the subtitle language whenever you want while playing the DVD, and turn it on or off whenever you want.
The angle is changed to the selected angle. In Shuffle or Program Play mode, the system repeats the titles or tracks in the shuffled or programmed order. The starting point point A is set. Newest bit rate range Indicates the transition of bit rate of the playback picture for a period up to the present. If it is a dual-layer DVD, the system indicates which layer is being read.
In this case, the sections show still images. Most settings and adjustments are required to be set when you first use the system. Using the Setup Display Using the setup display, you can do the initial setup, adjusting the picture, etc. The selected main item is highlighted.
The default settings are underlined. Note When you select a language that is not recorded on the DVD, one of the recorded languages is automatically selected except for the The digits change to asterisks , and the display for confirming the password appears.
The default setting is underlined.
0コメント